Handy’s warranty expired. So it’s time to experiment.(>ᴗ•)
First of all, I want to say that many people wrote that it is bad to use Handy with heavy weight. I tried to solve this problem for myself. I simply made active cooling of the Handy motor. (o_O)
It looks like this.
I had to turn the motor 180 degrees and put a radiator and fan inside the Handy. I had to insert two heatsinks on top of each other with great difficulty. They had to be cut to fit.
It was very difficult. But there is plenty of room next to the Handy motor. I think it would be interesting if the Handy 2 had active cooling.( ᵔ ⩊ ᵔ )
With active cooling, I was able to get rid of the rubber bands holding the doll on top.
I was able to make a holder for the front. Now Lamb SexDance is maximally “immersive”.
Sample
I’m using a new version doll here.
It’s made of three. The weight remained only in the legs at 200 grams each.
The doll holder has changed too. It now weighs 180 grams instead of 290 grams.
The Handy holder has changed as well. It now looks like this.
And yes, the most important discovery I’ve made. This is the Tenga Air-Tech Squeeze. They fit my blow-up dolls perfectly, and they can also be used with Handy. You just need to add a 1cm spacer from the Handy holder. For me they’re perfect.
I recommend you give it a try.
I know I’m a little obsessed with immersiveness. But now it’s practically perfect. I’m happy with the result.
This version is much better than the first one. I hope you had fun reading it.( = ⩊ = )
And yes, I also want to write. This installation can be used without doll. Just with Handy as HandsFree holder.
Hi. I did a very strange remodeling of my Keon to hands free airdoll device. ＼(〇_ｏ)／
The design still needs to be finalized, but it’s already turned out very “immersive” for me.
Maybe someone will find my idea useful.
I’m not an expert. Do it all at your own risk.(×_×)
You need:
1.
Keon that’s not to be regretted, and upgraded to power supply.
Need to saw off the front panel without the ring.
I used this saw
You can do it with a wood saw like I did, but it’s better not to. (￣ヘ￣)
You should use a special saw for plastic.
2.
Monitor mount with long extend.
I use Onkron G100.
3.
Special homemade or 3D printed mount for Keon.
I made it out of 12.7cm length, 11.3cm width, 1cm thick board, two metal angles 40x80x40 and two metal plates 40x90 and screws.
4.
Special homemade or 3D printed mount for AirDoll.
I use cardboard(5 layer), paper tape, cardboard tube, ties, plastic tube.
You need a structure that will support the doll under the arms and from the back and connects to the ring of Keon. This is the first model of the mount. It hasn’t broken in 3 uses, but it needs to be redesigned.
5.
Torso AirDoll
This
You can use it this way, but I did a very strange but more “immersive” way.
I connected my doll with legs from
I put lead shot in the feet and next to the hole.(•ิ_•ิ)?
If you are adding weight you need to do a rubber band mount to the ceiling. If not, you don’t have to.
I use doll with this skin and onahole.
Here’s what I got. o( ❛ᴗ❛ )o
Video
I use THIS in Vr headset (for 2D videos too) and with my last MMD it’s very “immersive”, but I need to come up with something for reverse cowgirl.
If there was something similar I apologize, I got to this design in a week of testing. First I made a similar design for The Handy, but it’s been very hard to get a grip. So I came up with this design, mostly because I bought new Keon on clearance for $88.
I hope that’s clear.
I think this could be adapted for OSR2 or SR6 if you make a very small tilt angle and not add weight. If you have them you can try it and write what you get.
You can leave your suggestions on how the design can be improved. I would be grateful. (>⩊<)