This is because the VESA mount wasn’t properly secured during testing. If the VESA mount is properly secured, this issue should not occur. I will test it again and post it to the community.
- The difference lies in the WiFi connection and the device’s ability to move without relying on a data source.
- In theory, no additional receivers are needed. The FLESHLIGHT receiver and half-moon receiver can adapt to a wide range of toys.
- The theoretical lifespan is 2000 hours, primarily depending on the motor.
- Yes, it is possible.
- Yes, it has higher integration. If the motor breaks, it can be replaced, but if the chip breaks, it cannot be (although it’s unclear in what scenarios the chip might break, such as liquid entering and damaging the circuit?).
1 Like
The biggest challenge at the moment is transportation and how to repair damages incurred during use at a low cost. Otherwise, it cannot be commercialized and can only be used for DIY purposes.
Would this be usable with HereSphere?
Looks very interesting in any case, would probably check this out if my Handy dies on me
1 Like
It can be done
Obviously they will test it, as its one of the key reasons to go for a stronger device. Which is why any limits the device has must be handled within the device itself so users cannot exceed it.
If users could change the firmware themselve to exceed those limits, thats something else, but thats where you can at least mark the firmware itself as safe or unsafe. (and im quite sure most users will just go with safe)
That the device becomes more expensive from improvements isnt a problem. The handy, launch, autoblow etc all have similar pricing, and as long as you are still significantly below that, you have a good competing product (and the margin is like a 50% higher price here, and potentialy even more).
Looks very interesting for me
But i’m not sure how i would mount it on a desk in a good way. I know it has VESA support but so far i can’t find any good mount that is small and can be adjusted up and down and also angle back and forward.
I would also prefer if my fleshlight case would be attached on the upper part of the case, the slim part. Just in case accidental slipping out from the sleeve, then it would feel safer to not have the machine so close. also it would make it less bulky at the entrence. Maybe it is possible with the straps that are included.
Wet Syncbot still gets me the feeling like that if you angle it well and use it at low suction and rotation. Slurps you right up.
1 Like
The strap can do it, hahaha. If you can’t find a VESA mount, you can use the handle. Unless it’s a very intense script, it should be stable enough for use.
What kind of motor is used in this?
We have replaced the WiFi connection method with Bluetooth for the following reasons:
- WiFi connections can be affected by network environments during use, leading to potential device lag for some users. However, this issue is difficult to troubleshoot.
- Because T-CODE is concise enough, Bluetooth data transmission itself will be more stable (with minimal impact from external environments). Testing has shown that in Polled Update mode, Bluetooth connection is nearly indistinguishable from USB connection.
- Bluetooth serial port supports Multifunplayer and VAM.
- In the future, we may introduce more gameplay features based on Bluetooth serial port.
Therefore, for users who placed orders until today, we will ship the WiFi + Bluetooth version. Starting from tomorrow, we will remove WiFi support and only support Bluetooth.
2 Likes
In india how to buy?
This does look interesting. Can it connect directly to Heresphere using the native bluetooth functionality HS provides?
Also, with these kinds of devices I’ve read in the past that owning one means replacing parts often, potential overheating and generally accepting that it’s a “DIY quality” device with a limited lifespan. Is that still true today?
If there’s an easy way to use it hands-free in bed I might buy this.
I expect it to reach THE HANDY’s quality, but to be honest, it’s hard to determine how long a product will last right after it’s released. However, a single-axis structure is simpler than the SR6’s, and I think its lifespan depends on the motor’s lifespan (of course, breaking the casing from a fall is also a likely damage). The convenience of playing in bed doesn’t depend on the device but rather on your VESA mount.
MultiFunPlayer supports Heresphere as a video player, you may wanna have it in between.
Dunno about connecting it straight from Heresphere. This device uses Bluetooth virtual COM port which means it is recognized as a serial device. If Heresphere uses the Buttplug.io library then there could be a way.
I made a review of this device in case you’ve missed it…
I have the feeling that FUNSR1 limits the stroke length even more than the Handy at higher speed. Is this due to a limitation in the firmware? Any chance to get this firmware to set a higher limitation myself, @renwoxing ?
I’m not their staff but I’m interested in the ssr1 as a whole -
Could you please try to select “PolledUpdate” in your MultiFunPlayer’s “Update settings” and see if it makes any difference? My hypothesis is that it handles faster actions better under this mode - haven’t verified this.
There’s no point to using someone else’s server when you can wire everything locally.
If the content is on someone else’s server, there is.
I understand that people aren’t happy about being “trapped” in proprietary ecosystems, but the variation in content and low threshold compared to downloading everything and manually getting different apps to sync is a game changer.
Read the threads here on eroscripts about the procedures for how to get things to run and sync, and compare that to buying a Handy, entering a 8 letter code into a box once, and then you’re off.
There is definitely a point!
1 Like